Wednesday, 23 October 2013

3D Design Day 3

On the last day of 3DD, we were given the task to create paper bridges. We were also given about an hour to do so which I thought was quite difficult especially with no inspiration. It was harder to come up with ideas today than the day before as  they wanted more spontaneous ideas from us and we had to use our sketchbooks to make them. 
I decided to design quite simple structures. The first bridge in the picture I decided to make non symmetrical as I thought it would be interesting so one half has a longer roof than the other. Shapes like those were created due to a shorter time span given to us which I think is sometimes good as you are sometimes more creative when a deadline is near.


Here I decided to do a bridge less conventional with paths crossing and separating from each other but on the other side it was just one straight part. Again I thought of not being symmetrical with my bridges and trying to make them unique and I wanted to create something that would potentially be a unusual user experience.


For this bridge, I was inspired by a futuristic transportation system which relies on suction and air force to help the person get there they are going. This was probably the fastest bridge I made as I wanted to increase the amount of bridges I had in the short amount of time.


This bridge was designed more like a tower or building and I thought that it would be an interesting bridge to walk though as the holes cast shadows. This was probably my favourite to make as it was so simple and  relied on the paper chain method where every side is the same.



Our last task of the day was to create a bridge from cardboard, elastic bands, tape and bamboo sticks. We were given an hour and a half to do this task which was quite a short time but with 6 of us in a group everyone had their roles to do. This was a very difficult task to do as it relied on communication between all of us, because of the short time, because of the materials given to us to use and because we did not know what size the car that had to drive over it was.

 


We decide to use the bamboo sticks as the road for the car, giving it two main paths for each wheel to ride over. We made the paths about 4 sticks wide and taped them together. This was probably the easiest part of the whole making process.
In the original plans we were meant to have a cardboard spiral rotating around the bridge like a spring. We made this using cardboard which I scored and then we made holes and joined them together using rubber bands. We made modifications to this as it was not going around diagonally so we ended up cutting it again.


At this point in the making we were almost finished and we were using bamboo to support the main paths for the car on top. 
We also added cardboard to the end of the bamboo points in order for the car to come onto the bridge. This was not a part of our design originally but we realised that we need to add this like the other groups in our class.





We tried to test out the spiral roof of the bridge lastly and join it to the bamboo sticks using the elastic bands in the same way we joined the pieces of cardboard. This was difficult as it was group effort to make sure it was the right way and everything was joined correctly. We then decided it was too long and mad it into squares to just attach to some of the bridge.

We joint this using tape.



I don't have a video for the car going over our bridge but it went over good with a few implications. One of the implications was the amount of tape on the bamboo as it was not smooth enough for the remote car to drive. Also I had to help keep it from driving off of the bridge as not all of it had walls to protect the car.

Overall, I enjoyed this pathway as it helped broaden the way I came up with ideas. It helped me when I got stuck with ideas and to find inspiration from the smaller things such as everyday objects or food. In terms of sketchbook work there is a huge stark contrast between any pathway I did. The way we were asked to lay out ideas was rough and did not mean that it had to be neat.

3D Design Day 2

On day 2 of 3DD we had to design holders made from spaghetti to hold 3 plastic balls . Firstly we had to design the holders in our sketchbooks. I had aimed today to try to think and create as many ideas as possible. I wanted to learn from the day before in which I focused on the functionality instead of the aesthetics. I designed a round cage type holder using two pieces of spaghetti on each line. This design originated from a criss cross idea with the balls sitting in the top grooves.

When making this holder I encountered very few problems as it did not require me cutting the spaghetti at all. The only problems encountered were that the spaghetti when hot glue was used on it got soft and sometimes became very brittle and flexible which I did not want and the position of the supporting pieces of spaghetti to get the 3rd ball to sit within the structure. To solve these problems I had to control the amount of glue I was using so that it didn't heat up so fast. I also had to make sure I had the pasta in the right position as every bond was permanent. 

When finished with the structure I decided to test it out with the balls then took photos of it using lights to create shadows. When looking at it again, I liked the idea of this shape as every piece of spaghetti connected to each other and did not need any breaking to create it. I also liked the fact that every side of this structure looked different at different angles although it is the same around it.








The last task of the day we had to create paper shields to protect our ball holders from a heavy weight which would land on top of it. The aim was to keep everything intact when the weight hit the protection. I found this task problematic because of the structure of my ball holder. In order to protect it I would either need to stuff the middle and have a sheet type shield on top or have a material which was thick shield the outside from the weight. We were only allowed to use paper to protect it which is quite thin. I decided to use cones made from paper to hold the structure tightly together and created rolls of paper to keep other parts of it upright as some of it was breaking apart because I wanted to test out the right ways to protect the holder.

In this picture, you can see that parts of the holder had broken off and was beyond repair. I realised at this point in making the paper shield, that it would not be able to cover and protect the holder because of the shape. If I had made this shorter or flatter (which would have included me breaking the spaghetti and would have been more time consuming) it would not have looked as neat as it was made as a final product. I also may have been able to create a shield for it as then it would have been a smaller holder to protect.

I finally had to turn the structure on its side as it was missing a few pieces due to me stretching holes with paper tubes. I feel like this task was not successful as my structure wasn't suitable for a shield to go over it. I could not think of a way to protect this properly because the structure was so open.

Here is a video of all of our classes structures being destroyed:

3D Design Day 1

On the first day of 3D Design we were introduced to the notion of turning unusual subjects into objects. We were firstly asked to make an animal into a mobile phone.


To design a bus stop using the numbers of our houses/ where we lived.
We were then asked to use our soles on our shoes as inspiration in order to design a piece of jewellery. I decided to design a bracelet which on one side was alligned with other parts of the bracelet but on the other the parts get longer from the wrist downwards.
I thought that this was one of the most difficult tasks which was to design a guide for a shopping centre and it had to include a path to the train station and a car park. I thought that this was difficult because we made a set shape.
To design a boat using the shapes: a square, a circle and a triangle.
To design a light made from our favourite piece of clothing. I chose a t-shirt with the Mickey Mouse print repeated all over it. I chose this because I thought it would be cool to have

To transform a human into an animal. I chose a snake as it was similar to the movie Sssssss and I thought that that animal transformation was interesting and unique.
To draw a random shape and then transform it into a pair of shoes with laces and soles.
I thought that this part of the task was the most interesting as we had to turn our favourite fruit or vegetable into a rabbit hutch. I chose a kiwi and initially I thought that this was difficult as I had drawn the kiwi not long enough for two rabbits. I then extended it and thought that it was a good idea to add windows and a door at the open sliced end of the
We had to design a seat for two people and a cat to sit on. The shape used was purely spontaneous and random. By creating this it became unique to every single person as no one could copy
All of these tasks were quite quick and because of this we created a lot of ideas. I think that this is important as a creative person to create so many ideas rapidly especially as we usually have deadlines to meet. This collection of ideas can be of low quality but it is to just to record ideas and to create things that we would not usually create.

After that task on the paper, we were asked to make something 3D. For the second task of the day we were asked to hold a plastic bottle 20cm off of the ground. Other conditions of this task was only using from hand to elbows worth of masking tape. I chose to do something simple which was a box but when testing it out on my own bottle, it was successful at first but then collapsed in the middle.

I made the box using a typical box layout on A1 paper and cutting the shape out then using the masking tape to hold it all together.
I then decided to add paper stumps to support it in the inside. I did this by rolling up paper into tubes and making slots for the paper to slot into itself as I had only a small amount of masking tape left. Adding these gave the whole box support as without it it could not withstand the weight put on it.


I then added small people to give the cube a sense of scale and I think it also makes the photos look more interesting and then it looks like the cube then has a purpose.







The last task of the day was to create a chair like object which could withstand our own weight and using 10 cardboard sheets and masking tape. 



The initial idea was that I would have a hexagon shell made from one of the cardboard sheets  and have smaller hexagons inside to hold the weight of myself.  All of these hexagons would be scored on the inside. But due to time constraints, I had to put paper into that empty space.

I felt like at the end of this day I did not grasp idea of the task. During the crit, I saw that others chose to focus on the aesthetics rather than the purpose whereas I did vice versa and was quite disappointed with my result. There were others which looked quite interesting and different and didn't work so I will try to think about being open to all of my own ideas.